Hello 30Watts
Removed farmland mappings.
Please keep yourself to the instructions

Hello
Here I removed your landuse mapping as well

Hello 30Watts. Thanks for mapping here.
I review work done by (new) mappers to check if they comply with the instructions and are of a good quality.
A few remarks.
Please keep yourself to the instructions.
This is a building only project. Please map accordingly.
The Imagery to be used is the MAXAR imagery. You mapped with BING, which is much older and show no newer buildings and shows also buildings which has been demolished or not altered.
btw. apart of a few landuse mappings, which I removed, did you not map buildings at all here !
I checking your other mappings as well
Best regards

Hello Jason DiNapoli. Thanks for mapping here as well. A question. Despite the instructions you mapped with the Bing imagery (rather old. Maxar is much more recent and shows more buildings)
Did you select Bing imagery or came it as default. I am asking this because when I open this task in iDeditor the Maxar imagery has been selected automatic. Thus the prescribed imagery.
Please let me know.
Best regards

Hello jnavarro_. Thanks for mapping on this project. You did a rather good job. We pay extra attention on new mappers work and advise if and how they can improve their mappings.
A few remarks.
First. this is a building only project. Don't bother about other objects like highways,
Please be as accurate as possible by following the outlines of buildings and do not include several buildings in 1 mapping.
Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

please restrict yourself to mapping of buildings as mentioned in the instructions.
You mapped here a few residential areas which make no sense when it is just a small part of a bigger village.
Best regards

Rectification. Please forget my previous message about residential areas. ( wrong addressee)
Best regards

please restrict yourself to mapping of buildings as mentioned in the instructions.
You mapped here a few residential areas which make no sense when it is just a small part of a bigger village.
Best regards

Thanks for mapping here.
A few remarks. You tend to map clusters or blocks of buildings as 1 (big) building. Please map each building individually,
Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello Claire. Thanks for mapping here.
A few remarks. You tend to map clusters or blocks of buildings as 1 (big) building. Please map each building individually,
Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello Vincenzeo516
Thanks for mapping here.
A few remarks. Buildings ought to be tagged as building=yes. Not as landuse=residential. That tag is suitable to tag a village etc as a total.

Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello Christian
Thanks for mapping on this project
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions.
This is a building only project , No need to map hilghways. Please concentrate on buildings which is the most urgent job.
Best regards and keep mapping

Hello Emy, Thanks for mapping here
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions

Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello
Thanks for mapping here
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions

Hello Thanks for mapping
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions

Hello. Thanks for mapping here,
A few remarks
Please pay attention on the accuracy of your mappings. Sometimes to map oversized.
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions
Best regards

Hello. thanks for mapping on this project
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions

Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello. Thanks for mapping here.
You mapped quite a lot. Great !
a few remarks.
most buildings are strict rectangular. Please map them with just 4 nodes. Because the imagery is taken under a certain angle it seems that the rooftop is a bit aside. Just map that strait forwarding. L shaped buildings with 6 nodes

Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions,
Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it. Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings.

Hello. Thanks for mapping

Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery and prescribed in the instructions

Did you noticed the "issue triangle" on the right hand menu in iDeditor? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it. Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degrees angle the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degrees corners
See this picture (example) https://drive.google.com/open?id=1gjraDKIuYKQ9c7asnOlA4ioeZDty195U
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello. Thanks for mapping here
A request. Please map more accurate. You map buildings a bit oversized and you combine a few buildings to 1 mapped building. Please map each building individual.
Please use the Maxar Std Imagery as the primary source. More recent and actual than the BING imagery. And prescribed in the instructions

Best regards