Hi Henning.
try this in ID editor
Ctr-Shift-M and draw a line (2)
zoom in not further than 5 mtr
in JOSM you can measure the widht at best with the round building tool
Zoom in rather close and draw a circle.
on the bottom line you will see the diameter. under 2.5 - 3 mtr. It will be most of the time a path.
Best regards
Frans

Hi, Tom Holland. Thanks for mapping here
Please read the instructions which imagery to be used and what to be mapped.
You mapped from an old imagery, Bing, despite MAXAR P was instructed.
You mapped a lot of tracks leading to nowhere. Please map only highways which connects settlement, hamlets etc.
Best regards and keep mapping.

Hi David
Just a remark. I noticed that you tag paths ( as width as max 1.5 mtr ) as track.
Mostly the are just accessible by foot, motorbike, and livestock.
Please keep that in consideration when you map those highways in rural areas
Thanks and best regards

Hello hebolz
Just a remark. I noticed that you tag paths ( as width as max 1.5 mtr ) as track.
Mostly the are just accessible by foot, motorbike, and livestock.
Please keep that in consideration when you map those highways in rural areas
Thanks and best regards

Hello Steven. Thanks for mapping here
A remark. You did not square a lot of buildings. Please keep an eye on that and square all buildings with the Q key in iDeditor
Did you noticed the "issue triangle" on the right hand menu? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
See this picture
https://drive.google.com/file/d/1gjraDKIuYKQ9c7asnOlA4ioeZDty195U/view
Did you have seen and read these pages ?
https://learnosm.org/en/hot-tips/
Best regards and keep mapping

Hallo Willem. Ik controleer mappings en zie dat je consequent gebouwen mapt als building-house.
Zie instructies. Tagging moet zijn building=yes
bedankt

Hi. Main reason is to use first Maxar as it is pretty good to map from. Esri is a difficult one.
But things change while you are working.
The MAXAR Standard ( not the Maxar P) is as far we now can see the most recent and shows the same new objects as the Esri.
So please use the Maxar S imagery here

Hi. Main reason is to use first Maxar as it is pretty good to map from. Esri is a difficult one.
But things change while you are working.
The MAXAR Standard ( not the Maxar P) is as far we now can see the most recent and shows the same new objects as the Esri.
So please use the Maxar S imagery heren.

Another remark. Please highways a requested. small paths etc leading to farmland are not required / Pleas do not connect nodes of highways to nodes of other objects, areas or buildings.
Best regards

Hello. Thanks for mapping here.
Please use the tag building=yes for all buildings.
You tag paths inbetween fields as unclassified highways. That is to much honor. 1.5 - 1.8 mtr wide is more a path or at best a track( when you can see wheeltracks of a 4x 4). I change that.

Mhogers, please refresh your knowlede how to tag highways here. See the WIKI

Hello MHogers. Please pay attention to the warnings the issue triangle gives (right hand menu) Find out what you did wrong and solve it please,

Hello Mannodej. Thanks for mapping.
A remark. You mapped an area and connected the nodes to a highway. This gives an error since this is not allowed, GPS driven nav systems cannot coop with that.
Please take that into account next mappings. I repair this

Hi Marian. Thanks for mapping.
Didn't you see the issue triangle on the right hand side of IDeditor ? It shows warnings if you do something wrong with mapping. In this case you was notified that the road you mapped did connect to nodes of the residential area which you mapped in the same session. Roads should never connect to other objects like buildings, landuse objects. and so on. Also let a road never cross buildings. GPS driven Nav systems cannot coop with that
best regards and keep mapping

Hello. Thanks for mapping on this project
Please use the Maxar P Imagery as the primary source. More recent and actual than the BING imagery.

Please square all rectangular buildings with the Q key of the iDeditor. A remark here. When your corners are not close enough to the 90 degr angel the Issue triangle on the right hand menu don't react so try to map more precise and close to the 90 degr corners

Did you noticed the "issue triangle" on the righthand menu? When a yellow or red dot pops up means that there are some issues. Mostly not squared buildings or connected nodes to other features. Please correct your own work before uploading it.
See this picture Review own work in iDeditor.jpg
Did you have seen these pages ?
https://learnosm.org/en/hot-tips/
Best regards and success with future mappings

Hello. Thanks for mapping.
Please map missing buildings visible on the MAXAR imagery. Select MAXAR P in iD editer.
Best regards and keep mapping

Hello. Thanks for mapping
a remark. You map several buildings close together as 1 building. Please map them individually. I remove these mappings. Please map them properly as well as adjust the poor mappings.
I invalidate this task
Also square the buildings you map. you squared hardly a building at next mappings

Hello . Please pay attention on the right hand menu where the issue triangle warns you when you make faults during mapping. Click on it and try to solve the issues before uploading your work.
Thanks

Hello Mary
Please do not combine several buildings into 1 big building. Please map each building separately
Thanks and keep mapping

Hallo. Bedankt voor het mappen.
een opmerking,
Gebouwen graag taggen als building=yes
geen andere tags.
Bedankt

Hello. Thanks for mapping here.
Please square the buildings you map with the Q key in iDeditor. Please check the issue triangle on the righthand menu of IDeditor for issues and try to solve them before uploading.
btw. You used the Bing imagery. Maxar is required for this project