Hello. Thanks for mapping on this project.
Please pay more attention on squaring of the buildings you map. Use the Q key in iDeditor after mapping a building.
Best regard and keep mapping

Hello. I saw your comment and took a look
You overlooked a number of smaller buildings. I noticed also a few mismapped buiildings ( not yours) and corrected them as well.
Your mappings are rather correct and accurate.
The most recent imagery here is ESRI which is a crime to work from,
Please map on other tasks first everything from the MAXAR imagery and then the balance from ESRI,
For the changes I made take a look to this webpage
https://overpass-api.de/achavi/?changeset=75149382
See the legend for info.
Best regards and keep mapping

Helo Dostadrian. Thanks for mapping on this project.
your mappings here are quite accurate.
Please tag buildings just as building=yes ( as per instructions) I corrected them
Best regards and keep mapping

Hello Lindazr . Thanks for mapping.
You mapped a number of very small objects as buildings. When you take a good look and measure them they appear to be cars.
I removed the mappings. Next to them there is building. I mapped it.
Best regards and keep mapping

It up to you
best regards

Hello. Thanks for mapping. It's a while ago that you mapped this , but due to a huge backlog on validating tasks it comes just now to my attention.
Some remarks. Please square the buildings you've mapped with the Q key in IDeditor.
You names several buildings, Do you have local knowledge? If not, Please stick to the generic tag building=yes
Local people will adjust the mappings later on.
Best regards and keep mapping.

Hello. Thanks for mapping.
A request. Please do not combine multiple buildings a 1 single building but map them each individual.
Best regards and keep mapping

Hello MKnight. Thanks for your comment, but am surprised by your answer which I did not expect from an expert in mapping as you.
We're not talking about millimetres offset and which imagery to be used, but about how tall buildings should be positioned and the accuracy of mapping.
I am not going to discuss this further here but invite you to continue this on the Validators channel of HOT on Slack.
So other validators can comment as well.
If you don't have an account, please register here
http://slack.hotosm.org
I look forward to your reaction
Best regards

Hello. Thanks for mapping here.
Please map more accurate. You often just draw a rectangular over a building instead of following the outlines. Also move the mapping to the footprint of a building when you map tall (high) buildings
Best regards and keep mapping

Hello. Thanks for mapping.
Please refresh your knowledge about highway taggings, You tag highways between a couple of houses as 'highway= tertiary. highway =unclassified fits better.
You also let nodes of these highways connect to buildings. These are errors. Never connect highways to other features. GPS driven nav systems cannot cope with that, ( a route should not go through buildings)
Also always square your buildings with the Q Key in id editor.
Please use the MAXAR imager for the most recent pictures.
Best regards and keep mapping

Hello Mhambi
Thanks for mapping.
A remark. Buildings ought to be tagged as
'building=yes' and no names like building.
I removed these tags

Hi. Thanks for mapping here. Please use Next mappings the Maxar Imagery. Most recent.
Did you seen the issue triangle on the righthand menu? A warning pops up.
You ought to correct these.
Always square the buildings you map !
Best regards and keep mapping

Hello. Thanks for mapping here.
Please square the buildings you map with the Q key in iDeditor. Please check the issue triangle on the righthand menu of IDeditor for issues and try to solve them before uploading.
btw. You used the Esri imagery. Bing or even Maxar is more clear to map from
There are still buildings to be mapped here
Best regards

Hello Monica
Thanks for mapping here.
A request. please map more precise and do not include more than 1 building in a mapping. Always square the buildings you have mapped with the Q key in IDeditor on the right hand menu as a last check. When a yellow or red dot pops up. there are issues with your mappings. Try to solve them before uploading. When you have no idea how to solve an issue. leave it to the validater and upload the mappings.
Best regards

Hello. A reaction a bit late. sorry for that
I am reviewing tasks and see quite a number of mappings. Sometimes your mappings are way oversized.Please map more accurate.
Best regards and keep mapping

Hello Garyjackson. Thanks for mapping.
a remark. Please square all the buildings you map with the Q key in ID editor.
On the right side menu in IDeditor is a warning triangle. when a yellow dot pops up it means that there are warnings and errors on the mappings. Please try to solve them. It might be also errors of other mappers. please repair them as well if possible,
Best regards and keep mapping

Hi Greg
I try to follow this wiki

waterway=river
It shows also that a waterway should not stop on a riverbank etc. ( see text)
The same with riverbanks. When I map them the river is mapped through it. You can with a bit of imagination also say that in your case a series of water (small lakes) are just water containing parts of the riverbank and the river should be tagged as intermittent=yes.
Leave me a reaction if you want.
Best regards

Hi Greg. I tried to recall this.
No Idea what's happens.
I must have moved the whole road by accident and did not noticed that.
Thanks anyhow. and see you on another project.
Best regards

Hi Greg. You've been very buzzy I see.
About Waterways and ponds/ water areas.
you often stop with mapping a river/stream on the edge of a area of water. like here.
When you connect the node of a river/stream to a node of that area, it gives an error. When it is a continuing stream please map them through the water area without letting nodes connect to each other. I've seen that as well with Highways ending on a residential area node.
Please keep that in mind at future mappings. ( you are working in JOSM, Why don't you check your work with the validation tool)
Best regards and keep mapping

Hello.Thanks for mapping.
I noticed that you use Bing for mapping here. Please read the instructions. There is a default imagery which comes together with the task. That should be used. Most recent.
You also re tagged highways tags track into grade 3. (this is just a qualification of the surface, The highway should be tagged as track. unclassified or
...
I corrected them into Path or track
You overlooked highways alongside the (dry) riverbed.
Best regards and keep mapping