Please take care not to let a highway crossing your mapped buildings.

Hi, I am a validator who review mapped tasks. Sorry to say, but your mappings are rather imprecise and not squared. Please review the training lessons to improve your mappings. Anyhow, thanks for mapping on this project

Hi Boggedy, I was looking into a validated part (task 13) to see what imagery was used because i could get the proposed imagery not loaded. You validated from a Bing imagery ? Did you have offset ? I noticed an offset of 10.75; 1.79 on the imagery as proposed.and 14 buildings crossing highway. Should a validator not correct this? ( and other warnings?)
I

Hi Kirstie
I noticed during validation that you did not square much buildings. Please square your buildings after each mapped building.
Thanks for mapping

Hi sophiechee
Why did you mark this task as completely mapped? You have mapped nearly half of the buildings.. Please don't mark a task as complete mapped since you are a beginner mapper. leave that to other more experienced mappers
Best regards

Hi Kirstie
Thanks for mapping

Make sure to square the corners of your buildings with the 'S' key in ID editor
You missed a number

Hi Danny
Thanks for mapping

Make sure to square the corners of your buildings with the 'S' key in ID editor
See your mappings here
https://overpass-api.de/achavi/?changeset=61032230

Hi Sarah, Thanks for mapping here.
About the quality of the mapping. You better follow the training courses how to map again . A few remarks. You map buildings much bigger than they are. You hardly square the corners of buildings which results in extra work for validaters.
you overlooked also buildings in the proximity of mapped buildings
you map also parts of a highway (visible between trees), as a building. When the Image on which you are working on is bad to read, change to another one ( here DG Standard.

Hi, after reviewing this task we found a lot of unsquared buildings. Please square each building with the S key (only rectangular buildings.) We have a lot repair work on badly mapped buildings.
Thank you

Hello, after reviewing this task I noticed that you hardly square buildings. Use the S key after each mapped building. We have a lot of repair work on bad mapped buildings
Thank you

Hi, During reviews of tasks I noticed that you often don't square buildings you have mapped. Please square your buildings next mappings. Thank you for mapping

Hello, after reviewing of this task we noticed still a lot of unsquared buildings. please use the S key in ID editor in future mappings
Thank you

Hi, The same message about squaring buildings is also valid for this set
Best regards

Hi, After reviewing this changeset there were many buildings left unsquared and with offset
Please Square your mapped buildings with the S key in ID editor in next mappings
Thanks

Hi, After reviewing tasks where you have mapped buildings, I notices that you regularly map buildings oversized. Please map as close to the image of buildings in future mappings. Thanks

Hi Michal, Thanks for mapping. During my review of this task I ran into a situation where you mapped buildings and connect nodes of these buildings to a road. This is not good. You need to avoid that. When people use this map for GPS navigation it should not be possible to show a route through a house. :-)
Thank you

Hello Patty, during reviewing this task for validation I noticed that you hardly squared a building. (155 out of 172 not squared.)
Please square each rectangular building with the S key in ID editor in future mappings.

Hi sconnolly. Thanks for mapping. One important issue. Your mappings are not very accurate and you did not square much buildings. Please check the learning wiki again how to map.
see this webpage with my adjustments
https://overpass-api.de/achavi/?changeset=61497064
Best regards

Hello Raphaellec, During review of mappings as validator I noticed that you sometimes map 2 buildings, not so close together, as 1 building. Please map each building as an individual building. Thank you for mapping

Hi Elusinda. After reviewing this task during validation I noticed a few points.
You connect often a highway to a building. This gives an error.
You often do not square a mapped building.
Please do that each time after mapping a rectangular building.
Often you connect 1 or more nodes of buildings. Try to avoid that. map buildings as individual buildings.