Glad to help, here's an example of such tagging: way/1258874282
I don't know of any software that implements the flashing speed limits but it's best to have the default road limit as the actual maxspeed value

Hello,
Thank you for correcting your tagging, although it is still not fully correct. Here is an example of how you should tag linear footway areas: relation/15397258

Hello there,
I noticed you have been mapping linear footways as pedestrian areas en masse. If you want to add the area of a footway you should tag it as area:highway=footway, as area=yes + highway=pedestrian is reserved for pedestrian areas such as squares or plazas. Not only is it incorrect mapping, it also poses problems for routers as they usually plan a route around the edge of the area instead of through the middle as with a simple linear way.

Hello there,
I noticed you have been mapping linear footways as pedestrian areas en masse. If you want to add the area of a footway you should tag it as area:highway=footway, as area=yes + highway=pedestrian is reserved for pedestrian areas such as squares or plazas. Not only is it incorrect mapping, it also poses problems for routers as they usually plan a route around the edge of the area instead of through the middle as with a simple linear way.

Да нет, в RU:* должны быть скорости для всех видов ТС как в Британии maxspeed:type, хотя в Польше видел везде проставлены явные ограничения. Всё равно ограничители стоят и шофёры будут ехать 90 везде... Короче пусть будет как до меня 100 просто

Thank you for this, there was a spree of mapping linear footways as pedestrian areas in Aberdeen, I'm still trying to fix that.

Теперь не знаю, вернуть или нет

Так должна же быть информация, что в России maxspeed:hgv не может превышать 90

Здравствуйте,
Я вижу вы поставили maxspeed=RU:motorway на трассе М-12. На данный момент стоят знаки 'дорога для автомобилей', которые не несут за собой скоростных ограничений. Следовательно, скоростной режим должен быть загородный (RU:rural). Повышенные ограничения для отдельных ТС уже присутствуют (maxspeed:motorcar, maxspeed:goods).

Здравствуйте,
Я вижу вы поставили maxspeed=RU:motorway на трассе М-12. На данный момент стоят знаки 'дорога для автомобилей', которые не несут за собой скоростных ограничений. Следовательно, скоростной режим должен быть загородный (RU:rural). Повышенные ограничения для отдельных ТС уже присутствуют (maxspeed:motorcar, maxspeed:goods).

Hello Will,
I was under the impression that the relation was indeed missing a piece since the section I added still has the ref 'CA 2', but it seems I need to do better research, my mistake. Should I revert my changeset and replace the ref with old_ref?
Regards,
Vas

Hello,
The correct way to tag the variable speed limit is maxspeed:conditional=20 mph @ flashing, not the other way around.

Hello there,
Can you provide a source for this landmass?

Hello,
I see you have been tagging footway areas as area=yes + highway=pedestrian. This isn't correct as that combination is for larger, non-linear pedestrian areas such as Castlegate or St Nicholas Square. You should instead tag the area around the already drawn linear footway as area:highway=footway

However, make sure to not tag it as area=yes + highway=pedestrian as that is for large non-linear pedestrian areas, for example Castlegate

Hello,
You have made a slight mistake here: relation/11296331/history
If you want to map a footway as an area you should draw the line the footway follows and tag it highway=footway as usual, then draw the area around it and simply tag it as area:highway=footway.

From the wiki:
"access=no, as any other access=* value may be overridden by more specific access tags."
It is easier to put access=no and specify the exceptions in this case and is a completely valid way of mapping.

You removed access=no but didn't add motor_vehicle=no which makes the other access tags invalid. Also 'psv' includes 'bus' and 'taxi'.

This section of bridge street is open to all motor vehicles going south, just leave the northbound bus gate lane at the traffic lights as it preserves the access restriction.

Hello, why is access=no incorrect? The street is under construction and I specified the allowed vehicle classes.